US Army11th Armored Cavalry Regiment BadgeSewing Label in OD Green...
US MilitaryChinstrap for ACH MICH HelmetNSN 8470-01-599-3851 Size:...
US Marine CorpsFoldable sleeping matImproved Sleeping Mat (ISM) of...
US Militaryself-adhesive repair patch in OCPColor: OCP (Operational...
US MilitaryHelmet pad oblong/ovalSuitable for ME, ACH, LWH, RBR and...
US MilitaryHelmet pad TrapezoidalSuitable for ME, ACH, LWH, RBR and...
US MilitaryHelmet pad CircularSuitable for ME, ACH, LWH, RBR and...
US MilitarySkydex helmet pad TrapezoidalSuitable for ME, ACH, LWH,...
US Military U.S. Heat Resistant...
U.S. Heat Resistant Barrel Glove, M2 .50 cal., M2 .50 cal.
Cal.50 M2, US GI
used in very good Condition
Made in USA
Warning: Last items in stock!
The M2 Machine Gun or Browning .50 Caliber Machine Gun is a heavy machine gun designed towards the end of World War I by John Browning. Its design is similar to Browning's earlier M1919 Browning machine gun, which was chambered for the .30-06 cartridge. The M2 uses the much larger and much more powerful .50 BMG cartridge, which was developed alongside and takes its name from the gun itself (BMG standing for Browning Machine Gun). It has been referred to as "Ma Deuce", in reference to its M2 nomenclature. The design has had many specific designations; the official designation for the current infantry type is Browning Machine Gun, Cal. .50, M2, HB, Flexible. It is effective against infantry, unarmored or lightly armored vehicles and boats, light fortifications and low-flying aircraft. The M2 machine gun has been produced longer than any other machine gun. The Browning .50 caliber machine gun has been used extensively as a vehicle weapon and for aircraft armament by the United States from the 1930s to the present. It was heavily used during World War II, the Korean War, the Vietnam War, the Falklands War, the Iraq War and the War in Afghanistan in the 2000s and 2010s. It is the primary heavy machine gun of NATO countries, and has been used by many other countries as well. The M2 has been in use longer than any other small arm in U.S. inventory except the .45 ACP M1911 pistol, also designed by John Browning. The current M2HB is manufactured in the U.S. by General Dynamics and U.S. Ordnance for use by the U.S. government, and for allies via Foreign Military Sales, as well as foreign manufacturers such as FN Herstal.
The M2 has varying cyclic rates of fire, depending on the model. The M2HB (heavy barrel) air-cooled ground gun has a cyclical rate of 450-575 rounds per minute. The early M2 water-cooled AA guns had a cyclical rate of around 450–600 rpm. The AN/M2 aircraft gun has a cyclic rate of 750–850 rpm; this increases to 1,200 rpm or more for AN/M3 aircraft guns fitted with electric or mechanical feed boost mechanisms. These maximum rates of fire are generally not achieved in use, as sustained fire at that rate will wear out the bore within a few thousand rounds, necessitating replacement. In addition to full automatic, the M2HB can be selected to fire single-shots or at less than 40 rounds per minute, or rapid fire for more than 40 rounds per minute. Slow and rapid firing modes use 5-7 round bursts with different lengths of pause between bursts. A U.S. Marine mans a .50 caliber machine gun as part of a security force during a training exercise with the 24th Marine Expeditionary Unit in November 2002. The M2 has an effective range of 1,830 metres (2,000 yd) and a maximum effective range of 2,000 metres (2,200 yd) when fired from the M3 tripod. In its ground-portable, crew-served role as the M2HB, the gun itself weighs 84 pounds (38 kg) and the assembled M3 tripod another 44 pounds (20 kg). In this configuration, the V-shaped "butterfly" trigger is located at the very rear of the weapon with a "spade handle" hand-grip on either side of it and the bolt release in the center. The spade handles are gripped and the butterfly trigger is depressed with one or both thumbs. Recently, new rear buffer assemblies have used squeeze triggers mounted to the hand grips, doing away with the butterfly triggers. When the bolt release is locked down by the bolt latch release lock on the buffer tube sleeve, the gun functions in fully automatic mode. Conversely, the bolt release can be unlocked into the up position resulting in single-shot firing (the gunner must press the bolt latch release to send the bolt forward). Unlike virtually all other modern machine guns, it has no safety (although a sliding safety switch has recently been fielded to USMC armorers for installation on their weapons and is standard-issue for the U.S. Army for all M2s). Troops in the field have been known to add an improvised safety measure against accidental firing by slipping an expended shell casing under the butterfly trigger. The upgraded M2A1 has a manual trigger block safety. Twin M2HB machine gun during a Pre-aimed Calibration Fire (PACFIRE) exercise in May 2005 Because the M2 was intentionally designed to operate in many configurations, it can be adapted to feed from the left or right side of the weapon by exchanging the belt-holding pawls, and the front and rear cartridge stops (three-piece set to include link stripper), then reversing the bolt switch. The operator must also convert the top-cover belt feed slide assembly from left to right hand feed as well as the spring and plunger in the feed arm. This will take a well trained individual less than two minutes to perform. The charging assembly may be changed from left to right hand charge. A right hand charging handle spring, lock wire and a little know how are all that are required to accomplish this. The M2 can be battle ready and easily interchanged if it is preemptively fitted with a retracting slide assembly on both sides of the weapon system. This eliminates the need to have the weapon removed from service to accomplish this task.